Username: Save?
Password:
Home Forum Links Search Login Register*
    News: Welcome to the TechnoWorldInc! Community!
Recent Updates
[November 08, 2024, 04:31:03 PM]

[November 08, 2024, 04:31:03 PM]

[November 08, 2024, 04:31:03 PM]

[November 08, 2024, 04:31:03 PM]

[November 08, 2024, 04:31:03 PM]

[October 17, 2024, 05:05:06 PM]

[October 17, 2024, 04:53:18 PM]

[October 17, 2024, 04:53:18 PM]

[October 17, 2024, 04:53:18 PM]

[October 17, 2024, 04:53:18 PM]

[September 09, 2024, 12:27:25 PM]

[September 09, 2024, 12:27:25 PM]

[September 09, 2024, 12:27:25 PM]
Subscriptions
Get Latest Tech Updates For Free!
Resources
   Travelikers
   Funistan
   PrettyGalz
   Techlap
   FreeThemes
   Videsta
   Glamistan
   BachatMela
   GlamGalz
   Techzug
   Vidsage
   Funzug
   WorldHostInc
   Funfani
   FilmyMama
   Uploaded.Tech
   MegaPixelShop
   Netens
   Funotic
   FreeJobsInc
   FilesPark
Participate in the fastest growing Technical Encyclopedia! This website is 100% Free. Please register or login using the login box above if you have already registered. You will need to be logged in to reply, make new topics and to access all the areas. Registration is free! Click Here To Register.
+ Techno World Inc - The Best Technical Encyclopedia Online! » Forum » THE TECHNO CLUB [ TECHNOWORLDINC.COM ] » Computer / Technical Issues » Hardware
  What Is A Crystal? And How To Test It
Pages: [1]   Go Down
  Print  
Author Topic: What Is A Crystal? And How To Test It  (Read 652 times)
Daniel Franklin
TWI Hero
**********


Karma: 3
Offline Offline

Posts: 16647


View Profile Email
What Is A Crystal? And How To Test It
« Posted: October 16, 2007, 04:32:22 PM »


Crystal are use to keep the frequency of the clock from drifting. If the signal from this clock stops, or is weak, or the pulses begin to vary, the electronic equipments might show intermittent faults or might stop altogether. The microprocessor pins that hold the crystal are usually called OSC IN and OSC OUT as shown in Figure 1 and the frequency is marked on the crystal. Typical examples of crystal oscillator frequency are 3.58MHZ, 4MHZ, 8MHZ, 24MHZ etc.


Testing Crystal
Crystals are quite fragile components because of their construction. Unlike a resistor or capacitor, if you drop one on the ground from a decent height, its 50-50 bet whether it will work again. Testing the crystal is not a breeze either. You cannot just take out your trusty multimeter and plug the crystal in it. In fact, there are three right ways to test a crystal: -

(a) Using Oscilloscope
A crystal produces a sine wave when excited. It is appropriate then, to see a waveform representative of a sine wave on the clock pins. If the clock is not functioning properly, replace the crystal. In most cases this should solve the problem since microprocessors are usually very reliable. Check the crystal with power on.

(b) Frequency Counter
Frequency Counter can be use to check the frequency of the crystal. The reading must be taken when the equipment power is switch “on”. Place the probe of frequency counter to the crystal pin and read the measurement. Be sure that your frequency counter meter has the range that is higher than the crystal frequency you are measuring.

(c) Crystal Checker
With this method, usually the crystal is placed in the feedback network of a transistor oscillator. If it oscillates and the LED is lighten up, this mean that the crystal is working. If the crystal doesn’t work, the LED stays off. Instead of using LED, some other crystal checker uses a panel meter to indicate if the crystal is working or not.

Jestine Yong is a electronic repairer and writer. For more information about electronic repair please visit his website at http://www.noahtec.com

Logged

Pages: [1]   Go Up
  Print  
 
Jump to:  

Copyright 2006-2023 TechnoWorldInc.com. All Rights Reserved. Privacy Policy | Disclaimer
Page created in 0.135 seconds with 24 queries.